diff --git a/config/generic-bigtreetech-skr-v1.4.cfg b/config/generic-bigtreetech-skr-v1.4.cfg
new file mode 100644
index 00000000..58024310
--- /dev/null
+++ b/config/generic-bigtreetech-skr-v1.4.cfg
@@ -0,0 +1,144 @@
+# This file contains common pin mappings for the BIGTREETECH SKR V1.4
+# board. To use this config, the firmware should be compiled for the
+# LPC1768 or LPC1769(Turbo).
+
+# See the example.cfg file for a description of available parameters.
+
+[stepper_x]
+step_pin: P2.2
+dir_pin: P2.6
+enable_pin: !P2.1
+step_distance: .0125
+endstop_pin: !P1.29
+position_endstop: 0
+position_max: 235
+homing_speed: 50
+
+[stepper_y]
+step_pin: P0.19
+dir_pin: P0.20
+enable_pin: !P2.8
+step_distance: .0125
+endstop_pin: !P1.28
+position_endstop: 0
+position_max: 235
+homing_speed: 50
+
+[stepper_z]
+step_pin: P0.22
+dir_pin: !P2.11
+enable_pin: !P0.21
+step_distance: .0025
+endstop_pin: !P1.27
+position_endstop: 0.0
+position_max: 300
+
+[extruder]
+step_pin: P2.13
+dir_pin: !P0.11
+enable_pin: !P2.12
+step_distance: .010526
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: P2.7
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: P0.24
+control: pid
+pid_Kp: 22.2
+pid_Ki: 1.08
+pid_Kd: 114
+min_temp: 0
+max_temp: 260
+
+#[extruder1]
+#step_pin: P1.15
+#dir_pin: P1.14
+#enable_pin: !P1.16
+#heater_pin: P2.4
+#sensor_pin: P0.23
+#...
+
+[heater_bed]
+heater_pin: P2.5
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: P0.25
+control: pid
+pid_Kp: 54.027
+pid_Ki: 0.770
+pid_Kd: 948.182
+min_temp: 0
+max_temp: 130
+
+[fan]
+pin: P2.3
+
+[mcu]
+serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
+
+[printer]
+kinematics: cartesian
+max_velocity: 400
+max_accel: 500
+max_z_velocity: 10
+max_z_accel: 100
+
+
+########################################
+# TMC2208 configuration
+########################################
+
+# For TMC2208 UART
+#   1) Place jumpers based on configuration
+#   2) Uncomment below config
+
+#[tmc2208 stepper_x]
+#uart_pin: P1.10
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 250
+#
+#[tmc2208 stepper_y]
+#uart_pin: P1.9
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 250
+#
+#[tmc2208 stepper_z]
+#uart_pin: P1.8
+#microsteps: 16
+#run_current: 0.650
+#hold_current: 0.450
+#stealthchop_threshold: 30
+#
+#[tmc2208 extruder]
+#uart_pin: P1.4
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+#
+#[tmc2208 extruder1]
+#uart_pin: P1.1
+#microsteps: 16
+#run_current: 0.800
+#hold_current: 0.500
+#stealthchop_threshold: 5
+
+
+########################################
+# EXP1 / EXP2 (display) pins
+########################################
+
+[board_pins]
+aliases:
+    # EXP1 header
+    EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
+    EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
+    # EXP2 header
+    EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
+    EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
+    # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "ssp0"
+
+# See the sample-lcd.cfg file for definitions of common LCD displays.