mirror of https://github.com/Desuuuu/klipper.git
config: Add BIQU BX printer config (#4950)
Signed-off-by: Aaron DeLyser <bluwolf@gmail.com>
This commit is contained in:
adelyser
GitHub
parent
31cefe15cf
commit
c15d38b973
|
|
@ -0,0 +1,317 @@
|
|||
# This file contains common pin mappings for the BigTreeTech SKR SE BX.
|
||||
# To use this config, the firmware should be compiled for the
|
||||
# STM32H743 with a "128KiB bootloader". Additionally, GPIO pins PB5
|
||||
# and PE5 need to be set at microcontroller startup.
|
||||
|
||||
######################################################################
|
||||
# NOTE: In order enable the TFT70-BX display when the printer first
|
||||
# starts, add PB5 and PE5 to the `GPIO pins to set at micro-controller
|
||||
# startup` section when running "make menuconfig"
|
||||
######################################################################
|
||||
|
||||
# The "make flash" command does not work on the SKR SE BX. Instead,
|
||||
# after running "make", copy the generated "out/klipper.bin" file to a
|
||||
# file named "firmware.bin" on an SD card and then restart the SKR SE BX
|
||||
# with that SD card. After klipper has been flashed once to the board,
|
||||
# you can update klipper by leaving a microSD inserted and running the
|
||||
# scripts/flash-sd.sh script.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
########################################
|
||||
# Steppers
|
||||
########################################
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PG13
|
||||
dir_pin: !PG12
|
||||
enable_pin: !PG14
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
full_steps_per_rotation: 400
|
||||
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
||||
position_endstop: -13
|
||||
position_min: -13
|
||||
position_max: 250
|
||||
homing_speed: 30
|
||||
homing_retract_dist: 0
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB3
|
||||
dir_pin: !PD3
|
||||
enable_pin: !PB4
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
full_steps_per_rotation: 400
|
||||
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
||||
position_endstop: -7
|
||||
position_min: -7
|
||||
position_max: 250
|
||||
homing_speed: 30
|
||||
homing_retract_dist: 0
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PD7
|
||||
dir_pin: PD6
|
||||
enable_pin: !PG9
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
full_steps_per_rotation: 400
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_min: -2
|
||||
position_max: 250
|
||||
|
||||
[stepper_z1]
|
||||
step_pin: PA8
|
||||
dir_pin: PC9
|
||||
enable_pin: !PD2
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
full_steps_per_rotation: 400
|
||||
|
||||
[extruder]
|
||||
step_pin: PC14
|
||||
dir_pin: !PC13
|
||||
enable_pin: !PC15
|
||||
microsteps: 16
|
||||
rotation_distance: 24.031
|
||||
gear_ratio: 7:1
|
||||
full_steps_per_rotation: 200
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PC4
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PH4
|
||||
control: pid
|
||||
pid_Kp: 22.2
|
||||
pid_Ki: 1.08
|
||||
pid_Kd: 114
|
||||
min_temp: 0
|
||||
max_temp: 350
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 125,125
|
||||
speed: 200
|
||||
z_hop: 10
|
||||
z_hop_speed: 25
|
||||
|
||||
########################################
|
||||
# TMC2209 configuration
|
||||
########################################
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PG10
|
||||
diag_pin: ^PB11
|
||||
run_current: 0.800
|
||||
sense_resistor: 0.150
|
||||
driver_SGTHRS: 127
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PD4
|
||||
diag_pin: ^PB12
|
||||
run_current: 0.800
|
||||
sense_resistor: 0.150
|
||||
driver_SGTHRS: 137
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PD5
|
||||
run_current: 1.000
|
||||
sense_resistor: 0.150
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[tmc2209 stepper_z1]
|
||||
uart_pin: PC8
|
||||
run_current: 1.000
|
||||
sense_resistor: 0.150
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PI8
|
||||
run_current: 0.800
|
||||
sense_resistor: 0.150
|
||||
stealthchop_threshold: 0
|
||||
|
||||
########################################
|
||||
# PRINTER
|
||||
########################################
|
||||
|
||||
[mcu]
|
||||
serial: /dev/ttyAMA0
|
||||
restart_method: command
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 200
|
||||
max_accel: 1000
|
||||
max_z_velocity: 10
|
||||
max_z_accel: 1000
|
||||
|
||||
[fan]
|
||||
pin: PA5
|
||||
|
||||
[heater_fan extruder_fan]
|
||||
pin: PA6
|
||||
heater: extruder
|
||||
|
||||
[controller_fan controller_fan]
|
||||
pin: PA7
|
||||
idle_timeout: 300 # 5 minute timeout
|
||||
|
||||
[output_pin motor_power]
|
||||
pin: PI11
|
||||
value: 1
|
||||
|
||||
[idle_timeout]
|
||||
gcode:
|
||||
TURN_OFF_HEATERS
|
||||
M84
|
||||
SET_PIN PIN=screen VALUE=0
|
||||
SET_LED LED=led BLUE=0.0 RED=0.0 GREEN=0.0
|
||||
|
||||
[pause_resume]
|
||||
|
||||
########################################
|
||||
# DISPLAY
|
||||
########################################
|
||||
|
||||
[output_pin screen]
|
||||
pin: PB5
|
||||
value: 1
|
||||
|
||||
[display_status]
|
||||
|
||||
[gcode_button lcd_button]
|
||||
pin: PH8
|
||||
press_gcode:
|
||||
SET_PIN PIN=screen VALUE=1
|
||||
SET_LED LED=led BLUE=1.0 RED=1.0 GREEN=1.0
|
||||
|
||||
[output_pin beeper]
|
||||
pin: PA14
|
||||
pwm: True
|
||||
cycle_time: 0.001
|
||||
|
||||
########################################
|
||||
# LEDS
|
||||
########################################
|
||||
|
||||
[neopixel led]
|
||||
pin: PH3
|
||||
chain_count: 15
|
||||
|
||||
[neopixel knob]
|
||||
pin: PB1
|
||||
chain_count: 2
|
||||
|
||||
[delayed_gcode welcome]
|
||||
initial_duration: 0.1
|
||||
gcode:
|
||||
SET_LED LED=knob RED=0.0 BLUE=1.0 GREEN=0.0
|
||||
SET_LED LED=led RED=0.0 BLUE=1.0 GREEN=0.0
|
||||
G4 P1000
|
||||
SET_LED LED=led RED=1.0 BLUE=0.0 GREEN=0.0
|
||||
G4 P1000
|
||||
SET_LED LED=led RED=0.0 BLUE=0.0 GREEN=1.0
|
||||
G4 P1000
|
||||
SET_LED LED=led RED=1.0 BLUE=1.0 GREEN=1.0
|
||||
|
||||
########################################
|
||||
# BED
|
||||
########################################
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA4
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PH5
|
||||
control: watermark
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[probe]
|
||||
pin: PH2
|
||||
x_offset: -30.1
|
||||
y_offset: 26.78
|
||||
z_offset: 0
|
||||
speed: 5
|
||||
samples: 3
|
||||
samples_result: median
|
||||
sample_retract_dist: 3.0
|
||||
samples_tolerance: 0.006
|
||||
samples_tolerance_retries: 5
|
||||
|
||||
[bed_mesh]
|
||||
speed: 120
|
||||
mesh_min: 10,19.78
|
||||
mesh_max: 219.9,230
|
||||
probe_count: 4,4
|
||||
|
||||
[screws_tilt_adjust]
|
||||
screw1: 58,-7
|
||||
screw1_name: front left
|
||||
screw2: 245,-7
|
||||
screw2_name: front right
|
||||
screw3: 245,179
|
||||
screw3_name: rear right
|
||||
screw4: 58,179
|
||||
screw4_name: rear left
|
||||
speed: 100
|
||||
screw_thread: CCW-M3
|
||||
|
||||
########################################
|
||||
## MACROS
|
||||
########################################
|
||||
|
||||
# Slicer setup: "print_start NOZZLE=<temp> BED=<temp>
|
||||
# This macro does a preheat on the probe for better accuracy and needs
|
||||
# the temps passed in. examples:
|
||||
# Cura: PRINT_START BED={material_bed_temperature_layer_0} NOZZLE={material_print_temperature_layer_0}
|
||||
# PrusaSlicer: PRINT_START NOZZLE=[first_layer_temperature] BED=[bed_temperature]
|
||||
# Use PRINT_END for the slicer ending script
|
||||
[gcode_macro PRINT_START]
|
||||
gcode:
|
||||
# Turn on screen if it's not on
|
||||
SET_PIN PIN=screen VALUE=1
|
||||
G28
|
||||
G0 Z1
|
||||
# Warm up nozzle, not to full temps yet
|
||||
M104 S150
|
||||
# Set LED to Purple for bed heating
|
||||
SET_LED LED=led BLUE=0.94 RED=0.63 GREEN=0.13
|
||||
M117 Heating Bed
|
||||
|
||||
# Allow probe to warm up, then re-home Z
|
||||
M190 S60
|
||||
M105
|
||||
G4 P90000
|
||||
G28 Z
|
||||
|
||||
M190 S{params.BED}
|
||||
M105
|
||||
G90 # Ensure we are in absolute mode
|
||||
G21
|
||||
M83 # Set the extruder to relative mode
|
||||
G92 E0
|
||||
|
||||
# Set LED to Red for nozzle heating
|
||||
SET_LED LED=led BLUE=0.0 RED=1.0 GREEN=0.0
|
||||
M117 Heating Nozzle
|
||||
G0 X2 Y0 F6000
|
||||
G0 Z0.4
|
||||
M109 S{params.NOZZLE}
|
||||
M105
|
||||
# Set LED to white for printing
|
||||
SET_LED LED=led BLUE=1.0 RED=1.0 GREEN=1.0
|
||||
M117 Printing
|
||||
|
||||
# Purge Line
|
||||
G1 X120 E30 F1200
|
||||
G1 Y1
|
||||
G1 X2 E30 F1200
|
||||
G92 E0
|
||||
|
||||
G1 Z1.0 F600
|
||||
G92 E0
|
||||
G0 F9000
|
||||
G90 # Set back to Absolute mode
|
||||
|
|
@ -0,0 +1,3 @@
|
|||
# Base config file for STM32H743 ARM processor
|
||||
CONFIG_MACH_STM32=y
|
||||
CONFIG_MACH_STM32H743=y
|
||||
|
|
@ -190,6 +190,10 @@ CONFIG ../../config/generic-fysetc-s6-v2.cfg
|
|||
CONFIG ../../config/generic-fysetc-spider.cfg
|
||||
CONFIG ../../config/generic-mks-rumba32-v1.0.cfg
|
||||
|
||||
# Printers using the stm32h743
|
||||
DICTIONARY stm32h743.dict
|
||||
CONFIG ../../config/printer-biqu-bx-2021.cfg
|
||||
|
||||
# Printers using the stm32g0b1
|
||||
DICTIONARY stm32g0b1.dict
|
||||
CONFIG ../../config/generic-bigtreetech-skr-mini-e3-v3.0.cfg
|
||||
|
|
|
|||
Loading…
Reference in New Issue