mirror of https://github.com/Desuuuu/klipper.git
config: Add BigTreeTech SKR Pico V1.0 board (#5022)
Signed-off-by: Alan.Ma from BigTreeTech <tech@biqu3d.com>
This commit is contained in:
parent
4d3198d44d
commit
aa2ede4a8c
|
@ -0,0 +1,132 @@
|
|||
# This file contains common pin mappings for the BIGTREETECH SKR Pico V1.0
|
||||
# To use this config, the firmware should be compiled for the
|
||||
# RP2040 and USB / UART communication.
|
||||
|
||||
# The "make flash" command does not work on the SKR Pico V1.0. Instead,
|
||||
# after running "make", copy the generated "out/klipper.uf2" file
|
||||
# to the mass storage device in RP2040 boot mode
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: gpio11
|
||||
dir_pin: !gpio10
|
||||
enable_pin: !gpio12
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^gpio4
|
||||
position_endstop: 0
|
||||
position_max: 235
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: gpio9
|
||||
tx_pin: gpio8
|
||||
uart_address: 0
|
||||
run_current: 0.580
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[stepper_y]
|
||||
step_pin: gpio6
|
||||
dir_pin: !gpio5
|
||||
enable_pin: !gpio7
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: ^gpio3
|
||||
position_endstop: 0
|
||||
position_max: 235
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: gpio9
|
||||
tx_pin: gpio8
|
||||
uart_address: 2
|
||||
run_current: 0.580
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[stepper_z]
|
||||
step_pin: gpio19
|
||||
dir_pin: gpio28
|
||||
enable_pin: !gpio2
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: ^gpio25
|
||||
position_endstop: 0.0
|
||||
position_max: 250
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: gpio9
|
||||
tx_pin: gpio8
|
||||
uart_address: 1
|
||||
run_current: 0.580
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[extruder]
|
||||
step_pin: gpio14
|
||||
dir_pin: !gpio13
|
||||
enable_pin: !gpio15
|
||||
microsteps: 16
|
||||
rotation_distance: 33.500
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: gpio23
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: gpio27
|
||||
control: pid
|
||||
pid_Kp: 21.527
|
||||
pid_Ki: 1.063
|
||||
pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: gpio9
|
||||
tx_pin: gpio8
|
||||
uart_address: 3
|
||||
run_current: 0.650
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: gpio21
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: gpio26
|
||||
control: pid
|
||||
pid_Kp: 54.027
|
||||
pid_Ki: 0.770
|
||||
pid_Kd: 948.182
|
||||
min_temp: 0
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: gpio17
|
||||
|
||||
[heater_fan nozzle_cooling_fan]
|
||||
pin: gpio18
|
||||
|
||||
[heater_fan controller_fan]
|
||||
pin: gpio20
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 3000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[neopixel board_neopixel]
|
||||
pin: gpio24
|
||||
chain_count: 1
|
||||
color_order: GRB
|
||||
initial_RED: 0.3
|
||||
initial_GREEN: 0.3
|
||||
initial_BLUE: 0.3
|
||||
|
||||
#[bltouch]
|
||||
#sensor_pin: gpio22
|
||||
#control_pin: gpio29
|
||||
|
||||
#[filament_switch_sensor runout_sensor]
|
||||
#switch_pin: ^gpio16
|
Loading…
Reference in New Issue