diff --git a/config/printer-bq-hephestos-2014.cfg b/config/printer-bq-hephestos-2014.cfg
deleted file mode 100644
index 5d77696a..00000000
--- a/config/printer-bq-hephestos-2014.cfg
+++ /dev/null
@@ -1,99 +0,0 @@
-# This file contains pin mappings for the BQ Prusa i3 Hephestos from 2014
-# (https://www.reprap.org/wiki/Prusa_i3_Hephestos)
-# It was sold in kit form, and uses a RAMPS board with HD44780 display without
-# heated bed or any modern amenities.
-
-# To use this config, the firmware should be compiled for the AVR atmega2560.
-
-# See docs/Config_Reference.md for a description of parameters.
-
-[display]
-lcd_type: hd44780
-rs_pin: PH1
-e_pin: PH0
-d4_pin: PA1
-d5_pin: PA3
-d6_pin: PA5
-d7_pin: PA7
-encoder_pins: ^PC6, ^PC4
-click_pin:  ^!PC2
-kill_pin: ^!PG0
-
-[stepper_x]
-step_pin: PF0
-dir_pin: !PF1
-enable_pin: !PD7
-microsteps: 16
-rotation_distance: 40
-endstop_pin: ^!PE5
-position_endstop: 0
-position_max: 200
-homing_speed: 50
-
-[stepper_y]
-step_pin: PF6
-dir_pin: PF7
-enable_pin: !PF2
-microsteps: 16
-rotation_distance: 40
-endstop_pin: ^!PJ1
-position_endstop: 0
-position_max: 200
-homing_speed: 50
-
-[stepper_z]
-step_pin: PL3
-dir_pin: !PL1
-enable_pin: !PK0
-microsteps: 16
-rotation_distance: 0.8
-endstop_pin: ^!PD3
-position_endstop: 0
-position_max: 200
-homing_speed: 3
-
-[extruder]
-step_pin: PA4
-dir_pin: PA6
-enable_pin: !PA2
-microsteps: 16
-# measured extruding 100mm of filament with stock Hephestos extruder
-rotation_distance: 31.825
-nozzle_diameter: 0.400
-filament_diameter: 1.750
-heater_pin: PB4
-sensor_type: EPCOS 100K B57560G104F
-sensor_pin: PK5
-min_temp: 0
-max_temp: 250
-
-# 5 points for manual bed leveling that still leave room for accessing the stock screws
-[bed_screws]
-screw1: 40, 40
-screw2: 180, 40
-screw3: 180, 160
-screw4: 40, 160
-screw5: 110, 100
-
-[fan]
-pin: PH6
-
-[printer]
-kinematics: cartesian
-max_velocity: 300
-max_accel: 3000
-# Must limit Z velocity, since RAMPS does not have enough timer resolution
-max_z_velocity: 3
-max_z_accel: 100
-
-# Common EXP1 / EXP2 (display) pins
-[board_pins]
-aliases:
-    # Common EXP1 header found on many "all-in-one" ramps clones
-    EXP1_1=PC0, EXP1_3=PH0, EXP1_5=PA1, EXP1_7=PA5, EXP1_9=<GND>,
-    EXP1_2=PC2, EXP1_4=PH1, EXP1_6=PA3, EXP1_8=PA7, EXP1_10=<5V>,
-    # EXP2 header
-    EXP2_1=PB3, EXP2_3=PC6, EXP2_5=PC4, EXP2_7=PL0, EXP2_9=<GND>,
-    EXP2_2=PB1, EXP2_4=PB0, EXP2_6=PB2, EXP2_8=PG0, EXP2_10=<RST>
-    # Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
-    # Note, some boards wire: EXP2_8=<RST>, EXP2_10=PG0