config: Added Config for Creality Ender 5 Pro 2020 (#4836)

Signed-off-by:  Maxim Schessler <maxim.schessler@gmail.com>

config/printer-creality-ender5pro-2020.cfg

@@ -0,0 +1,101 @@
+# This file contains pin mappings for the stock 2020 Creality Ender 5
+# Pro with the 32-bit Creality 4.2.2 board. To use this config, during
+# "make menuconfig" select the STM32F103 with a "28KiB bootloader" and
+# with "Use USB for communication" disabled.
+
+# If you prefer a direct serial connection, in "make menuconfig"
+# select "Enable extra low-level configuration options" and select the
+# USART3 serial port, which is broken out on the 10 pin IDC cable used
+# for the LCD module as follows:
+# 3: Tx, 4: Rx, 9: GND, 10: VCC
+
+# Flash this firmware by copying "out/klipper.bin" to a SD card and
+# turning on the printer with the card inserted. The firmware
+# filename must end in ".bin" and must not match the last filename
+# that was flashed.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+[stepper_x]
+step_pin: PC2
+dir_pin: PB9
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PA5
+position_endstop: 220
+position_max: 220
+homing_speed: 50
+
+[stepper_y]
+step_pin: PB8
+dir_pin: PB7
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 40
+endstop_pin: ^PA6
+position_endstop: 220
+position_max: 220
+homing_speed: 50
+
+[stepper_z]
+step_pin: PB6
+dir_pin: PB5
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 4
+endstop_pin: ^PA7
+position_max: 300
+position_endstop: 0.0
+
+[extruder]
+max_extrude_only_distance: 100.0
+step_pin: PB4
+dir_pin: PB3
+enable_pin: !PC3
+microsteps: 16
+rotation_distance: 32.342
+nozzle_diameter: 0.400
+filament_diameter: 1.750
+heater_pin: PA1
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC5
+control: pid
+pid_kp: 24.831
+pid_ki: 1.346
+pid_kd: 114.532
+min_temp: 0
+max_temp: 260
+
+[heater_bed]
+heater_pin: PA2
+sensor_type: EPCOS 100K B57560G104F
+sensor_pin: PC4
+control: pid
+pid_kp: 66.429
+pid_ki: 1.197
+pid_kd: 921.707
+min_temp: 0
+max_temp: 135
+
+[fan]
+pin: PA0
+
+[mcu]
+serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
+restart_method: command
+
+[printer]
+kinematics: cartesian
+max_velocity: 300
+max_accel: 3000
+max_z_velocity: 5
+max_z_accel: 100
+
+[display]
+lcd_type: st7920
+cs_pin: PB12
+sclk_pin: PB13
+sid_pin: PB15
+encoder_pins: ^PB14, ^PB10
+click_pin: ^!PB2

test/klippy/printers.test

@@ -161,6 +161,7 @@ CONFIG ../../config/printer-creality-ender2pro-2021.cfg
 CONFIG ../../config/printer-creality-ender3-v2-2020.cfg
 CONFIG ../../config/printer-creality-ender3max-2021.cfg
 CONFIG ../../config/printer-creality-ender3pro-2020.cfg
+CONFIG ../../config/printer-creality-ender5pro-2020.cfg
 CONFIG ../../config/printer-creality-ender6-2020.cfg
 CONFIG ../../config/printer-creality-sermoonD1-2021.cfg
 CONFIG ../../config/printer-elegoo-neptune2-2021.cfg