mirror of https://github.com/Desuuuu/klipper.git
89 lines
1.5 KiB
INI
89 lines
1.5 KiB
INI
|
# This file contains common pin mappings for Anet E10 printer from
|
||
|
|
# 2018. To use this config, the firmware should be compiled for the
|
||
|
|
# AVR atmega1284p.
|
||
|
|
|
||
|
|
# Note that the "make flash" command does not work with Anet boards -
|
||
|
|
# the boards are typically flashed with this command:
|
||
|
|
# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
|
||
|
|
|
||
|
|
# See the example.cfg file for a description of available parameters.
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: PD7
|
||
|
|
dir_pin: PC5
|
||
|
|
enable_pin: !PD6
|
||
|
|
step_distance: .0125
|
||
|
|
endstop_pin: ^!PC2
|
||
|
|
position_endstop: -3
|
||
|
|
position_max: 220
|
||
|
|
position_min: -3
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: PC6
|
||
|
|
dir_pin: !PC7
|
||
|
|
enable_pin: !PD6
|
||
|
|
step_distance: .0125
|
||
|
|
endstop_pin: ^!PC3
|
||
|
|
position_endstop: -22
|
||
|
|
position_min: -22
|
||
|
|
position_max: 270
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: PB3
|
||
|
|
dir_pin: !PB2
|
||
|
|
enable_pin: !PA5
|
||
|
|
step_distance: .0025
|
||
|
|
endstop_pin: ^!PC4
|
||
|
|
position_endstop: 0.5
|
||
|
|
position_max: 300
|
||
|
|
homing_speed: 20
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: PB1
|
||
|
|
dir_pin: !PB0
|
||
|
|
enable_pin: !PD6
|
||
|
|
step_distance: .01
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: PD5
|
||
|
|
sensor_type: ATC Semitec 104GT-2
|
||
|
|
sensor_pin: PA7
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 27.0
|
||
|
|
pid_Ki: 1.3
|
||
|
|
pid_Kd: 136.09
|
||
|
|
min_temp: 10
|
||
|
|
max_temp: 250
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: PD4
|
||
|
|
sensor_type: ATC Semitec 104GT-2
|
||
|
|
sensor_pin: PA6
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 72.8
|
||
|
|
pid_Ki: 1.2
|
||
|
|
pid_Kd: 1100
|
||
|
|
min_temp: 10
|
||
|
|
max_temp: 130
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: PB4
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/ttyUSB0
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 1000
|
||
|
|
max_z_velocity: 20
|
||
|
|
max_z_accel: 100
|
||
|
|
|
||
|
|
[display]
|
||
|
|
lcd_type: st7920
|
||
|
|
cs_pin: PA4
|
||
|
|
sclk_pin: PA1
|
||
|
|
sid_pin:PA3
|