2021-08-10 16:01:06 +02:00
|
|
|
# This file contains common pin mappings for the BigTreeTech E3 RRF 1.1.
|
|
|
|
|
# To use this config, the firmware should be compiled for the
|
|
|
|
|
# STM32F407 with a "32KiB bootloader".
|
|
|
|
|
|
|
|
|
|
# The "make flash" command does not work on the E3 RRF 1.1. Instead,
|
|
|
|
|
# after running "make", copy the generated "out/klipper.bin" file to a
|
|
|
|
|
# file named "firmware.bin" on an SD card and then restart the E3 RRF
|
|
|
|
|
# 1.1 with that SD card.
|
|
|
|
|
|
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PD5
|
|
|
|
|
dir_pin: !PD4
|
|
|
|
|
enable_pin: !PD7
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
endstop_pin: ^PC0
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 235
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[tmc2209 stepper_x]
|
|
|
|
|
uart_pin: PD6
|
|
|
|
|
run_current: 0.580
|
|
|
|
|
stealthchop_threshold: 999999
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PD0
|
|
|
|
|
dir_pin: !PA15
|
|
|
|
|
enable_pin: !PD3
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
endstop_pin: ^PC1
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 235
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[tmc2209 stepper_y]
|
|
|
|
|
uart_pin: PD1
|
|
|
|
|
run_current: 0.580
|
|
|
|
|
stealthchop_threshold: 999999
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PC6
|
|
|
|
|
dir_pin: PC7
|
|
|
|
|
enable_pin: !PD14
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 8
|
|
|
|
|
endstop_pin: ^PC2
|
|
|
|
|
position_endstop: 0.0
|
|
|
|
|
position_max: 250
|
|
|
|
|
|
|
|
|
|
[tmc2209 stepper_z]
|
|
|
|
|
uart_pin: PD15
|
|
|
|
|
run_current: 0.580
|
|
|
|
|
stealthchop_threshold: 999999
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: PD12
|
|
|
|
|
dir_pin: !PD13
|
|
|
|
|
enable_pin: !PD10
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 33.500
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PB3
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PA0
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 21.527
|
|
|
|
|
pid_Ki: 1.063
|
|
|
|
|
pid_Kd: 108.982
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 250
|
|
|
|
|
|
|
|
|
|
[tmc2209 extruder]
|
|
|
|
|
uart_pin: PD11
|
|
|
|
|
run_current: 0.650
|
|
|
|
|
stealthchop_threshold: 999999
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PB4
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PA1
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 54.027
|
|
|
|
|
pid_Ki: 0.770
|
|
|
|
|
pid_Kd: 948.182
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 130
|
|
|
|
|
|
2022-07-19 19:02:51 +02:00
|
|
|
[heater_fan heatbreak_cooling_fan]
|
2021-08-10 16:01:06 +02:00
|
|
|
pin: PB6
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PB5
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_370025000247303034313331-if00
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 3000
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
|
|
|
|
|
|
|
|
|
# Warning: display section not tested!
|
|
|
|
|
|
|
|
|
|
[board_pins]
|
|
|
|
|
aliases:
|
|
|
|
|
# EXP1 header
|
|
|
|
|
EXP1_1=PE8, EXP1_3=PE7, EXP1_5=PB2, EXP1_7=PB1, EXP1_9=<GND>,
|
|
|
|
|
EXP1_2=PE9, EXP1_4=<RST>, EXP1_6=PE10, EXP1_8=PE11, EXP1_10=<5V>
|
|
|
|
|
|
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
