2018-07-08 05:10:45 +02:00
|
|
|
# This file contains the configurations and pin mappings for the
|
|
|
|
|
# Tronxy X8 using the CXY-V2-0508 board. To use this config file, the
|
|
|
|
|
# firmware should be compiled for the AVR ATmega1284p, 16MHz.
|
|
|
|
|
|
|
|
|
|
# Some Tronxy printers come without a bootloader present on the
|
|
|
|
|
# board. In that case, use MCUDude MightyCore ATmega1284p bootloader
|
|
|
|
|
# with TQFP44 Sanguino pinout. The package can be found at
|
|
|
|
|
# (https://github.com/MCUdude/MightyCore). Follow Klipper install
|
|
|
|
|
# instructions but instead of "make flash FLASH_DEVICE=/dev/ttyACM0",
|
|
|
|
|
# use the following command:
|
|
|
|
|
# avrdude -p atmega1284p -c arduino -b 115200 -P /dev/ttyUSB0 -U out/klipper.elf.hex
|
|
|
|
|
|
2020-11-17 00:47:32 +01:00
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
2018-07-08 05:10:45 +02:00
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/ttyUSB0
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PD7
|
|
|
|
|
dir_pin: PC5
|
|
|
|
|
enable_pin: !PD6
|
2020-12-14 15:09:19 +01:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 32
|
2018-07-08 05:10:45 +02:00
|
|
|
endstop_pin: ^!PC2
|
|
|
|
|
position_endstop: -47
|
|
|
|
|
position_max: 220
|
|
|
|
|
position_min: -47
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PC6
|
|
|
|
|
dir_pin: PC7
|
|
|
|
|
enable_pin: !PD6
|
2020-12-14 15:09:19 +01:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 32
|
2018-07-08 05:10:45 +02:00
|
|
|
endstop_pin: ^!PC3
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 220
|
|
|
|
|
position_min: 0
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PB3
|
|
|
|
|
dir_pin: !PB2
|
|
|
|
|
enable_pin: !PD6
|
2020-12-14 15:09:19 +01:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 8
|
2018-07-08 05:10:45 +02:00
|
|
|
endstop_pin: ^!PC4
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 210
|
|
|
|
|
homing_speed: 10
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: PB1
|
|
|
|
|
dir_pin: PB0
|
|
|
|
|
enable_pin: !PD6
|
2020-12-14 15:09:19 +01:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 31.779
|
2018-07-08 05:10:45 +02:00
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PD5
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PA7
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 22.2
|
|
|
|
|
pid_Ki: 1.08
|
|
|
|
|
pid_Kd: 114
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 275
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PD4
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PA6
|
|
|
|
|
control: watermark
|
|
|
|
|
max_delta: 2.0
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 150
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PB4
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 1000
|
|
|
|
|
max_z_velocity: 20
|
|
|
|
|
max_z_accel: 100
|
|
|
|
|
|
|
|
|
|
[display]
|
|
|
|
|
lcd_type: st7920
|
|
|
|
|
cs_pin: PA1
|
|
|
|
|
sclk_pin: PC0
|
|
|
|
|
sid_pin: PA3
|
