mirror of https://github.com/Desuuuu/klipper.git
85 lines
1.6 KiB
INI
85 lines
1.6 KiB
INI
|
# This file contains common pin mappings for the BIGTREETECH SKR V1.1
|
||
|
|
# board. To use this config, the firmware should be compiled for the
|
||
|
|
# LPC176x.
|
||
|
|
|
||
|
|
# The "make flash" command does not work on the SKR. Instead, after
|
||
|
|
# running "make", copy the generated "out/klipper.bin" file to a file
|
||
|
|
# named "firmware.bin" on an SD card and then restart the BIGTREETECH
|
||
|
|
# SKR V1.1 with that SD card.
|
||
|
|
|
||
|
|
# See the example.cfg file for a description of available parameters.
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: P0.4
|
||
|
|
dir_pin: !P0.5
|
||
|
|
enable_pin: !P4.28
|
||
|
|
step_distance: .0025
|
||
|
|
endstop_pin: P1.29
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 200
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: P2.1
|
||
|
|
dir_pin: P2.2
|
||
|
|
enable_pin: !P2.0
|
||
|
|
step_distance: .0025
|
||
|
|
endstop_pin: P1.27
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 200
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: P0.20
|
||
|
|
dir_pin: P0.21
|
||
|
|
enable_pin: !P0.19
|
||
|
|
step_distance: .0125
|
||
|
|
endstop_pin: !P1.25
|
||
|
|
position_endstop: 0.5
|
||
|
|
position_max: 200
|
||
|
|
|
||
|
|
#[stepper_z1]
|
||
|
|
#step_pin: P0.1
|
||
|
|
#dir_pin: P0.0
|
||
|
|
#enable_pin: !P0.10
|
||
|
|
#position_endstop: 0.5
|
||
|
|
#position_max: 200
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: P0.11
|
||
|
|
dir_pin: P2.13
|
||
|
|
enable_pin: !P2.12
|
||
|
|
step_distance: .002
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: P2.7
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: P0.24
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 22.2
|
||
|
|
pid_Ki: 1.08
|
||
|
|
pid_Kd: 114
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 250
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: P2.5
|
||
|
|
sensor_type: ATC Semitec 104GT-2
|
||
|
|
sensor_pin: P0.23
|
||
|
|
control: watermark
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 130
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: P2.3
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 3000
|
||
|
|
max_z_velocity: 5
|
||
|
|
max_z_accel: 100
|