2019-01-13 22:42:10 +01:00
|
|
|
# This file contains common pin mappings for the BIGTREETECH SKR V1.1
|
|
|
|
|
# board. To use this config, the firmware should be compiled for the
|
2019-06-20 17:23:30 +02:00
|
|
|
# LPC1768.
|
2019-01-13 22:42:10 +01:00
|
|
|
|
2020-11-17 00:47:32 +01:00
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
2019-01-13 22:42:10 +01:00
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: P0.4
|
|
|
|
|
dir_pin: !P0.5
|
|
|
|
|
enable_pin: !P4.28
|
|
|
|
|
step_distance: .0025
|
|
|
|
|
endstop_pin: P1.29
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 200
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: P2.1
|
|
|
|
|
dir_pin: P2.2
|
|
|
|
|
enable_pin: !P2.0
|
|
|
|
|
step_distance: .0025
|
|
|
|
|
endstop_pin: P1.27
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 200
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: P0.20
|
|
|
|
|
dir_pin: P0.21
|
|
|
|
|
enable_pin: !P0.19
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: !P1.25
|
|
|
|
|
position_endstop: 0.5
|
|
|
|
|
position_max: 200
|
|
|
|
|
|
|
|
|
|
#[stepper_z1]
|
|
|
|
|
#step_pin: P0.1
|
|
|
|
|
#dir_pin: P0.0
|
|
|
|
|
#enable_pin: !P0.10
|
|
|
|
|
#position_endstop: 0.5
|
|
|
|
|
#position_max: 200
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: P0.11
|
|
|
|
|
dir_pin: P2.13
|
|
|
|
|
enable_pin: !P2.12
|
|
|
|
|
step_distance: .002
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: P2.7
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: P0.24
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 22.2
|
|
|
|
|
pid_Ki: 1.08
|
|
|
|
|
pid_Kd: 114
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 250
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: P2.5
|
|
|
|
|
sensor_type: ATC Semitec 104GT-2
|
|
|
|
|
sensor_pin: P0.23
|
|
|
|
|
control: watermark
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 130
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: P2.3
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 3000
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
2019-02-08 00:16:07 +01:00
|
|
|
|
2019-08-20 03:40:20 +02:00
|
|
|
[board_pins]
|
|
|
|
|
aliases:
|
|
|
|
|
# EXP1 header
|
|
|
|
|
EXP1_1=P1.30, EXP1_3=P0.18, EXP1_5=P0.15, EXP1_7=<NC>, EXP1_9=<GND>,
|
|
|
|
|
EXP1_2=P2.11, EXP1_4=P0.16, EXP1_6=<NC>, EXP1_8=<NC>, EXP1_10=<5V>,
|
|
|
|
|
# EXP2 header
|
|
|
|
|
EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
|
|
|
|
|
EXP2_2=P0.15, EXP2_4=P1.23, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
|
|
|
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "ssp0"
|
|
|
|
|
|
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
