klipper-dgus/config/example-delta.cfg

# This file serves as documentation for config parameters of delta
# style printers. One may copy and edit this file to configure a new
# delta printer. Only parameters unique to delta printers are
# described here - see the "example.cfg" file for description of
# common config parameters.

# DO NOT COPY THIS FILE WITHOUT CAREFULLY READING AND UPDATING IT
# FIRST. Incorrectly configured parameters may cause damage.

# The stepper_a section describes the stepper controlling the front
# left tower (at 210 degrees). This section also controls the homing
# parameters (homing_speed, homing_retract_dist) and maximum tower
# length (position_max) for all towers.
[stepper_a]
step_pin: ar54
dir_pin: ar55
enable_pin: !ar38
step_distance: .01
endstop_pin: ^ar2
homing_speed: 50.0
position_endstop: 297.05
position_max: 297.55

# The stepper_b section describes the stepper controlling the front
# right tower (at 330 degrees)
[stepper_b]
step_pin: ar60
dir_pin: ar61
enable_pin: !ar56
step_distance: .01
endstop_pin: ^ar15
position_endstop: 297.05

# The stepper_c section describes the stepper controlling the rear
# tower (at 90 degrees)
[stepper_c]
step_pin: ar46
dir_pin: ar48
enable_pin: !ar62
step_distance: .01
endstop_pin: ^ar19
position_endstop: 297.05

[extruder]
step_pin: ar26
dir_pin: ar28
enable_pin: !ar24
step_distance: .0022
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: ar10
thermistor_pin: analog13
thermistor_type: ATC Semitec 104GT-2
control: pid
pid_Kp: 22.2
pid_Ki: 1.08
pid_Kd: 114
min_temp: 0
max_temp: 250

[heater_bed]
heater_pin: ar8
thermistor_pin: analog14
thermistor_type: EPCOS 100K B57560G104F
control: watermark
min_temp: 0
max_temp: 130

# Extruder print fan (omit section if fan not present)
#[fan]
#pin: ar9
#hard_pwm: 1

[mcu]
serial: /dev/ttyACM0
pin_map: arduino

[printer]
kinematics: delta
#   This option must be "delta" for linear delta printers.
max_velocity: 300
#   Maximum velocity (in mm/s) of the toolhead relative to the
#   print. This limits the velocity of the toolhead relative to the
#   print - at the extreme end of the print envelope the delta axis
#   steppers themselves may briefly exceed this speed by up to 3
#   times. This parameter must be specified.
max_accel: 3000
#   Maximum acceleration (in mm/s^2) of the toolhead relative to the
#   print. This limits the acceleration of the toolhead relative to
#   the print - at the extreme end of the print envelope the delta
#   axis steppers may briefly exceed this acceleration by up to 3
#   times. This parameter must be specified.
max_z_velocity: 200
#   For delta printers this limits the maximum velocity (in mm/s) of
#   moves with z axis movement. This setting can be used to reduce the
#   maximum speed of up/down moves (which require a higher step rate
#   than other moves on a delta printer). The default is to use
#   max_velocity for max_z_velocity.
delta_arm_length: 333.0
#   Length (in mm) of the diagonal rods that connect the linear axes
#   to the print head. This parameter must be provided.
delta_radius: 174.75
#   Radius (in mm) of the horizontal circle formed by the three linear
#   axis towers. This parameter may also be calculated as:
#    delta_radius = smooth_rod_offset - effector_offset - carriage_offset
#   This parameter must be provided.