2018-01-16 06:20:56 +01:00
|
|
|
# This file contains pin mappings for the Tronxy X5S (circa 2017). To
|
|
|
|
|
# use this config, the firmware should be compiled for the AVR
|
|
|
|
|
# atmega1284p.
|
|
|
|
|
|
2018-03-24 14:32:37 +01:00
|
|
|
# UPDATE 2018
|
|
|
|
|
# Newest Tronxy's are coming with bootloader present, so follow
|
|
|
|
|
# klipper install instructions but instead of "make flash FLASH_DEVICE=/dev/ttyACM0"
|
|
|
|
|
# use:
|
|
|
|
|
# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
|
|
|
|
|
|
2018-01-16 06:20:56 +01:00
|
|
|
# Note, a number of Melzi boards are shipped without a bootloader. In
|
|
|
|
|
# that case, an external programmer will be needed to flash a
|
|
|
|
|
# bootloader to the board (for example, see
|
|
|
|
|
# http://www.instructables.com/id/Flashing-a-Bootloader-to-the-CR-10/
|
|
|
|
|
# ). Once that is done, one should be able to use the standard "make
|
|
|
|
|
# flash" command to flash Klipper.
|
|
|
|
|
|
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PD7
|
|
|
|
|
dir_pin: !PC5
|
|
|
|
|
enable_pin: !PD6
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^!PC2
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 330
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PC6
|
|
|
|
|
dir_pin: !PC7
|
|
|
|
|
enable_pin: !PD6
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^!PC3
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 310
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PB3
|
|
|
|
|
dir_pin: PB2
|
|
|
|
|
enable_pin: !PD6
|
2018-02-25 22:00:55 +01:00
|
|
|
step_distance: .0025
|
2018-01-16 06:20:56 +01:00
|
|
|
endstop_pin: ^!PC4
|
|
|
|
|
position_endstop: 0.5
|
|
|
|
|
position_max: 400
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: PB1
|
|
|
|
|
dir_pin: PB0
|
|
|
|
|
enable_pin: !PD6
|
|
|
|
|
step_distance: .0111
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PD5
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PA7
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 22.2
|
|
|
|
|
pid_Ki: 1.08
|
|
|
|
|
pid_Kd: 114
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 275
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PD4
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PA6
|
|
|
|
|
control: watermark
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 150
|
|
|
|
|
|
2018-03-24 14:32:37 +01:00
|
|
|
[verify_heater heater_bed]
|
|
|
|
|
# adjust for personal bed setup, this prevents stock heated bed from issuing
|
|
|
|
|
# false positive heating errors due to slow temperature increase
|
|
|
|
|
check_gain_time: 600
|
|
|
|
|
|
2018-01-16 06:20:56 +01:00
|
|
|
[fan]
|
|
|
|
|
pin: PB4
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/ttyUSB0
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: corexy
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 1000
|
|
|
|
|
max_z_velocity: 20
|
|
|
|
|
max_z_accel: 100
|
2018-03-07 21:12:58 +01:00
|
|
|
|
|
|
|
|
[display]
|
|
|
|
|
lcd_type: st7920
|
|
|
|
|
cs_pin: PA1
|
|
|
|
|
sclk_pin: PC0
|
|
|
|
|
sid_pin: PA3
|
|
|
|
|
|
|
|
|
|
# buttons are:
|
|
|
|
|
# PD2, PD3: encoder
|
|
|
|
|
# PA5: click
|
