klipper-dgus/docs/G-Codes.md

This document describes the commands that Klipper supports. These are
commands that one may enter into the OctoPrint terminal tab.

# G-Code commands

Klipper supports the following standard G-Code commands:
- Move (G0 or G1): `G1 [X<pos>] [Y<pos>] [Z<pos>] [E<pos>] [F<speed>]`
- Dwell: `G4 P<milliseconds>`
- Move to origin: `G28 [X] [Y] [Z]`
- Turn off motors: `M18` or `M84`
- Wait for current moves to finish: `M400`
- Select tool: `T<index>`
- Use absolute/relative distances for extrusion: `M82`, `M83`
- Use absolute/relative coordinates: `G90`, `G91`
- Set position: `G92 [X<pos>] [Y<pos>] [Z<pos>] [E<pos>]`
- Set speed factor override percentage: `M220 S<percent>`
- Set extrude factor override percentage: `M221 S<percent>`
- Set acceleration: `M204 S<value>`
- Get extruder temperature: `M105`
- Set extruder temperature: `M104 [T<index>] [S<temperature>]`
- Set extruder temperature and wait: `M109 [T<index>] S<temperature>`
  - Note: M109 always waits for temperature to settle at requested
    value
- Set bed temperature: `M140 [S<temperature>]`
- Set bed temperature and wait: `M190 S<temperature>`
  - Note: M190 always waits for temperature to settle at requested
    value
- Set fan speed: `M106 S<value>`
- Turn fan off: `M107`
- Emergency stop: `M112`
- Get current position: `M114`
- Get firmware version: `M115`

For further details on the above commands see the
[RepRap G-Code documentation](http://reprap.org/wiki/G-code).

Klipper's goal is to support the G-Code commands produced by common
3rd party software (eg, OctoPrint, Printrun, Slic3r, Cura, etc.) in
their standard configurations. It is not a goal to support every
possible G-Code command. Instead, Klipper prefers human readable
["extended G-Code commands"](#extended-g-code-commands).

If one requires a less common G-Code command then it may be possible
to implement it with a custom Klipper gcode_macro (see
[example-extras.cfg](../config/example-extras.cfg) for details). For
example, one might use this to implement: `G10`, `G11`, `G12`, `G29`,
`G30`, `G31`, `M42`, `M80`, `M81`, etc.

## G-Code SD card commands

Klipper also supports the following standard G-Code commands if the
"virtual_sdcard" config section is enabled:
- List SD card: `M20`
- Initialize SD card: `M21`
- Select SD file: `M23 <filename>`
- Start/resume SD print: `M24`
- Pause SD print: `M25`
- Set SD position: `M26 S<offset>`
- Report SD print status: `M27`

## G-Code display commands

The following standard G-Code commands are available if a "display"
config section is enabled:
- Display Message: `M117 <message>`
- Set build percentage: `M73 P<percent>`

## Other available G-Code commands

The following standard G-Code commands are currently available, but
using them is not recommended:
- Offset axes: `M206 [X<offset>] [Y<offset>] [Z<offset>]` (Use
  SET_GCODE_OFFSET instead.)
- Get Endstop Status: `M119` (Use QUERY_ENDSTOPS instead.)

# Extended G-Code Commands

Klipper uses "extended" G-Code commands for general configuration and
status.  These extended commands all follow a similar format - they
start with a command name and may be followed by one or more
parameters. For example: `SET_SERVO SERVO=myservo ANGLE=5.3`. In this
document, the commands and parameters are shown in uppercase, however
they are not case sensitive. (So, "SET_SERVO" and "set_servo" both run
the same command.)

The following standard commands are supported:
- `QUERY_ENDSTOPS`: Probe the axis endstops and report if they are
  "triggered" or in an "open" state. This command is typically used to
  verify that an endstop is working correctly.
- `GET_POSITION`: Return information on the current location of the
  toolhead.
- `SET_GCODE_OFFSET [X=<pos>|X_ADJUST=<adjust>]
  [Y=<pos>|Y_ADJUST=<adjust>] [Z=<pos>|Z_ADJUST=<adjust>]`: Set a
  positional offset to apply to future G-Code commands. This is
  commonly used to virtually change the Z bed offset or to set nozzle
  XY offsets when switching extruders. For example, if
  "SET_GCODE_OFFSET Z=0.2" is sent, then future G-Code moves will
  have 0.2mm added to their Z height. If the X_ADJUST style parameters
  are used, then the adjustment will be added to any existing offset
  (eg, "SET_GCODE_OFFSET Z=-0.2" followed by "SET_GCODE_OFFSET
  Z_ADJUST=0.3" would result in a total Z offset of 0.1).
- `PID_CALIBRATE HEATER=<config_name> TARGET=<temperature>
  [WRITE_FILE=1]`: Perform a PID calibration test. The specified
  heater will be enabled until the specified target temperature is
  reached, and then the heater will be turned off and on for several
  cycles. If the WRITE_FILE parameter is enabled, then the file
  /tmp/heattest.txt will be created with a log of all temperature
  samples taken during the test.
- `TURN_OFF_HEATERS`: Turn off all heaters.
- `SET_VELOCITY_LIMIT [VELOCITY=<value>] [ACCEL=<value>]
  [ACCEL_TO_DECEL=<value>] [SQUARE_CORNER_VELOCITY=<value>]`: Modify
  the printer's velocity limits. Note that one may only set values
  less than or equal to the limits specified in the config file.
- `SET_HEATER_TEMPERATURE HEATER=<heater_name> [TARGET=<target_temperature>]`:
  Sets the target temperature for a heater. If a target temperature is
  not supplied, the target is 0.
- `SET_PRESSURE_ADVANCE [EXTRUDER=<config_name>] [ADVANCE=<pressure_advance>]
  [ADVANCE_LOOKAHEAD_TIME=<pressure_advance_lookahead_time>]`:
  Set pressure advance parameters. If EXTRUDER is not specified, it
  defaults to the active extruder.
- `STEPPER_BUZZ STEPPER=<config_name>`: Move the given stepper forward
  one mm and then backward one mm, repeated 10 times. This is a
  diagnostic tool to help verify stepper connectivity.
- `MANUAL_PROBE [SPEED=<speed>]`: Run a helper script useful for
  measuring the height of the nozzle at a given location. If SPEED is
  specified, it sets the speed of TESTZ commands (the default is
  5mm/s). During a manual probe, the following additional commands are
  available:
  - `ACCEPT`: This command accepts the current Z position and
  concludes the manual probing tool.
  - `ABORT`: This command terminates the manual probing tool.
  - `TESTZ Z=<value>`: This command moves the nozzle up or down by the
    amount specified in "value". For example, `TESTZ Z=-.1` would move
    the nozzle down .1mm while `TESTZ Z=.1` would move the nozzle up
    .1mm. The value may also be `+`, `-`, `++`, or `--` to move the
    nozzle up or down an amount relative to previous attempts.
- `Z_ENDSTOP_CALIBRATE [SPEED=<speed>]`: Run a helper script useful
  for calibrating a Z position_endstop config setting. See the
  MANUAL_PROBE command for details on the parameters and the
  additional commands available while the tool is active.
- `RESTART`: This will cause the host software to reload its config
  and perform an internal reset. This command will not clear error
  state from the micro-controller (see FIRMWARE_RESTART) nor will it
  load new software (see
  [the FAQ](FAQ.md#how-do-i-upgrade-to-the-latest-software)).
- `FIRMWARE_RESTART`: This is similar to a RESTART command, but it
  also clears any error state from the micro-controller.
- `SAVE_CONFIG`: This command will overwrite the main printer config
  file and restart the host software. This command is used in
  conjunction with other calibration commands to store the results of
  calibration tests.
- `STATUS`: Report the Klipper host software status.
- `HELP`: Report the list of available extended G-Code commands.

## Custom Pin Commands

The following command is available when an "output_pin" config section
is enabled:
- `SET_PIN PIN=config_name VALUE=<value>`

## Servo Commands

The following commands are available when a "servo" config section is
enabled:
- `SET_SERVO SERVO=config_name [WIDTH=<seconds>] [ENABLE=<0|1>]`
- `SET_SERVO SERVO=config_name [ANGLE=<degrees>] [ENABLE=<0|1>]`

## Manual stepper Commands

The following command is available when a "manual_stepper" config
section is enabled:
- `MANUAL_STEPPER STEPPER=config_name [ENABLE=[0|1]]
  [SET_POSITION=<pos>]
  [MOVE=<pos> SPEED=<speed> [STOP_ON_ENDSTOP=1]]`: This command will
  alter the state of the stepper. Use the ENABLE parameter to
  enable/disable the stepper. Use the SET_POSITION parameter to force
  the stepper to think it is at the given position. Use the MOVE
  parameter to request a movement to the given position at the given
  SPEED. If STOP_ON_ENDSTOP is specified then the move will end early
  should the endstop report as triggered (use STOP_ON_ENDSTOP=-1 to
  stop early should the endstop report not triggered).

## Probe

The following commands are available when a "probe" config section is
enabled:
- `PROBE`: Move the nozzle downwards until the probe triggers.
- `QUERY_PROBE`: Report the current status of the probe ("triggered"
  or "open").
- `PROBE_ACCURACY [REPEAT=<times>] [SPEED=<speed mm/s>] [X=<x pos>]
  [Y=<y pos>] [Z=<z height>]`: Calculate the maximum, minimum, average,
  median and standard deviation. The default values are: REPEAT=10,
  SPEED=probe config speed, X=current X, Y=current Y and Z=10.
- `PROBE_CALIBRATE [SPEED=<speed>]`: Run a helper script useful for
  calibrating the probe's z_offset. See the MANUAL_PROBE command for
  details on the parameters and the additional commands available
  while the tool is active.

## BLTouch

The following command is available when a "bltouch" config section is
enabled:
- `BLTOUCH_DEBUG COMMAND=<command>`: This sends a command to the
  BLTouch. It may be useful for debugging. Available commands are:
  pin_down, touch_mode, pin_up, self_test, reset.

See [Working with the BL-Touch](BLTouch.md) for more details.

## Delta Calibration

The following commands are available when the "delta_calibrate" config
section is enabled:
- `DELTA_CALIBRATE [METHOD=manual]`: This command will probe seven
  points on the bed and recommend updated endstop positions, tower
  angles, and radius. If METHOD=manual is specified then the manual
  probing tool is activated - see the MANUAL_PROBE command above for
  details on the additional commands available while this tool is
  active.
- `DELTA_ANALYZE`: This command is used during enhanced delta
  calibration. See [Delta Calibrate](Delta_Calibrate.md) for details.

## Bed Tilt

The following commands are available when the "bed_tilt" config
section is enabled:
- `BED_TILT_CALIBRATE [METHOD=manual]`: This command will probe the
  points specified in the config and then recommend updated x and y
  tilt adjustments. If METHOD=manual is specified then the manual
  probing tool is activated - see the MANUAL_PROBE command above for
  details on the additional commands available while this tool is
  active.

## Mesh Bed Leveling

The following commands are available when the "bed_mesh" config
section is enabled:
- `BED_MESH_CALIBRATE [METHOD=manual]`: This command probes the bed
  using generated points specified by the parameters in the
  config. After probing, a mesh is generated and z-movement is
  adjusted according to the mesh. If METHOD=manual is specified then
  the manual probing tool is activated - see the MANUAL_PROBE command
  above for details on the additional commands available while this
  tool is active.
- `BED_MESH_OUTPUT`: This command outputs the current probed z values
  and current mesh values to the terminal.
- `BED_MESH_MAP`: This command probes the bed in a similar fashion
  to BED_MESH_CALIBRATE, however no mesh is generated.  Instead,
  the probed z values are serialized to json and output to the
  terminal.  This allows octoprint plugins to easily capture the
  data and generate maps approximating the bed's surface.  Note
  that although no mesh is generated, any currently stored mesh
  will be cleared.
- `BED_MESH_CLEAR`: This command clears the mesh and removes all
  z adjustment.  It is recommended to put this in your end-gcode.
- `BED_MESH_PROFILE LOAD=<name> SAVE=<name> REMOVE=<name>`: This
  command provides profile management for mesh state.  LOAD will
  restore the mesh state from the profile matching the supplied name.
  SAVE will save the current mesh state to a profile matching the
  supplied name.  Remove will delete the profile matching the
  supplied name from persistent memory.  Note that after SAVE or
  REMOVE operations have been run the SAVE_CONFIG gcode must be run
  to make the changes to peristent memory permanent.

## Bed Screws Helper

The following commands are available when the "bed_screws" config
section is enabled:
- `BED_SCREWS_ADJUST`: This command will invoke the bed screws
  adjustment tool. It will command the nozzle to different locations
  (as defined in the config file) and allow one to make adjustments to
  the bed screws so that the bed is a constant distance from the
  nozzle.

## Z Tilt

The following commands are available when the "z_tilt" config section
is enabled:
- `Z_TILT_ADJUST`: This command will probe the points specified in the
  config and then make independent adjustments to each Z stepper to
  compensate for tilt.

## Dual Carriages

The following command is available when the "dual_carriage" config
section is enabled:
- `SET_DUAL_CARRIAGE CARRIAGE=[0|1]`: This command will set the active
  carriage. It is typically invoked from the activate_gcode and
  deactivate_gcode fields in a multiple extruder configuration.

## TMC2130

The following command is available when the "tmc2130" config section
is enabled:
- `DUMP_TMC STEPPER=<name>`: This command will read the TMC2130 driver
  registers and report their values.

## Endstop adjustments by stepper phase

The following commands are available when an "endstop_phase" config
section is enabled:
- `ENDSTOP_PHASE_CALIBRATE [STEPPER=<config_name>]`: If no STEPPER
  parameter is provided then this command will reports statistics on
  endstop stepper phases during past homing operations. When a STEPPER
  parameter is provided it arranges for the given endstop phase
  setting to be written to the config file (in conjunction with the
  SAVE_CONFIG command).

## Force movement

The following commands are available when the "force_move" config
section is enabled:
- `FORCE_MOVE STEPPER=<config_name> DISTANCE=<value>
  VELOCITY=<value>`: This command will forcibly move the given stepper
  the given distance (in mm) at the given constant velocity (in
  mm/s). No acceleration is performed; no boundary checks are
  performed; no kinematic updates are made; other parallel steppers on
  an axis will not be moved. Use caution as an incorrect command could
  cause damage! Using this command will almost certainly place the
  low-level kinematics in an incorrect state; issue a G28 afterwards
  to reset the kinematics. This command is intended for low-level
  diagnostics and debugging.
- `SET_KINEMATIC_POSITION [X=<value>] [Y=<value>] [Z=<value>]`: Force
  the low-level kinematic code to believe the toolhead is at the given
  cartesian position. This is a diagnostic and debugging command; use
  SET_GCODE_OFFSET and/or G92 for regular axis transformations. If an
  axis is not specified then it will default to the position that the
  head was last commanded to. Setting an incorrect or invalid position
  may lead to internal software errors. This command may invalidate
  future boundary checks; issue a G28 afterwards to reset the
  kinematics.

## Send message (respond) to host

The following commands are availabe when the "respond" config section is
enabled.
  - `M118 <message>`: echo the message prepended with the configured default
    prefix (or `echo: ` if no prefix is configured).
  - `RESPOND MSG="<message>"`: echo the message prepended with the configured default
    prefix (or `echo: ` if no prefix is configured).
  - `RESPOND TYPE=echo MSG="<message>"`: echo the message prepended with `echo: `.
  - `RESPOND TYPE=command MSG="<message>"`: echo the message prepended with `// `.
    Octopint can be configured to respond to these messages (e.g.
    `RESPOND TYPE=command MSG=action:pause`).
  - `RESPOND TYPE=error MSG="<message>"`: echo the message prepended with `!! `.
  - `RESPOND PREFIX=<prefix> MSG="<message>"`: echo the message prepended with `<prefix>`
    (The `PREFIX` parameter will take priority over the `TYPE` parameter)

## Pause Resume

The following commands are available when the "pause_resume" config section
is enabled:
  - `PAUSE`:  Pauses the current print.  The current position is captured for
  restoration upon resume.
  - `RESUME [VELOCITY=<value>]`: Resumes the print from a pause, first restoring
  the previously captured position.  The VELOCITY parameter determines the speed
  at which the tool should return to the original captured position.