2019-06-09 04:30:07 +02:00
|
|
|
# This file contains pin mappings for the Wanhao Duplicator i3 Plus
|
|
|
|
|
# Mark II. To use this config, the firmware should be compiled for the
|
|
|
|
|
# AVR atmega2560.
|
|
|
|
|
|
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PF7
|
|
|
|
|
dir_pin: !PK0
|
|
|
|
|
enable_pin: !PF6
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^!PF0
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 200
|
|
|
|
|
homing_speed: 30.0
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PK2
|
|
|
|
|
dir_pin: !PK3
|
|
|
|
|
enable_pin: !PE4
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^!PA2
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 200
|
|
|
|
|
homing_speed: 30.0
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PK5
|
|
|
|
|
dir_pin: PK7
|
|
|
|
|
enable_pin: !PK4
|
|
|
|
|
step_distance: .0025
|
|
|
|
|
endstop_pin: probe:z_virtual_endstop
|
|
|
|
|
position_max: 180
|
|
|
|
|
position_min: -0.5
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: PF4
|
|
|
|
|
dir_pin: PF5
|
|
|
|
|
enable_pin: !PF3
|
|
|
|
|
step_distance: 0.010417
|
|
|
|
|
nozzle_diameter: 0.300
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PG5
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PF1
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 20.982
|
|
|
|
|
pid_Ki: 0.725
|
|
|
|
|
pid_Kd: 151.861
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 260
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PE5
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PK6
|
|
|
|
|
control: watermark
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 110
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PE3
|
|
|
|
|
|
|
|
|
|
[probe]
|
|
|
|
|
pin: !PH3
|
|
|
|
|
z_offset: 1.0
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 800
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
|
|
|
|
|
|
|
|
|
[bed_mesh]
|
2019-12-17 20:15:49 +01:00
|
|
|
mesh_min: 20,20
|
|
|
|
|
mesh_max: 190,130
|
2019-06-09 04:30:07 +02:00
|
|
|
probe_count: 4,4
|
