mirror of https://github.com/Desuuuu/klipper.git
141 lines
2.4 KiB
INI
141 lines
2.4 KiB
INI
|
# This is a Klipper configuration for TronXY X5SA, with
|
||
|
|
# CXY-V6 motherboard.
|
||
|
|
|
||
|
|
|
||
|
|
# === FLASHING WITH STOCK BOOTLOADER ===
|
||
|
|
# You should make firmware for STM32F103 with bootloader offset
|
||
|
|
# at 0x8008800 (Chitu v6 Bootloader). Uncheck USB, and leave default
|
||
|
|
# serial settings.
|
||
|
|
#
|
||
|
|
# Use "./chitu_crypt.py out/klipper.bin" to generate update.cbz.
|
||
|
|
# Put `update.cbz` onto SD card, and reboot the printer.
|
||
|
|
# It will be automatically installed, and you will be able to update it this way.
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||
|
|
restart_method: command
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: corexy
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 7000
|
||
|
|
max_accel_to_decel: 7000
|
||
|
|
max_z_velocity: 25
|
||
|
|
max_z_accel: 30
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: PE5
|
||
|
|
dir_pin: !PE6
|
||
|
|
enable_pin: !PC13
|
||
|
|
step_distance: .006275
|
||
|
|
endstop_pin: !PG10
|
||
|
|
position_endstop: -1
|
||
|
|
position_min: -1
|
||
|
|
position_max: 350
|
||
|
|
homing_speed: 50
|
||
|
|
homing_retract_dist: 10
|
||
|
|
second_homing_speed: 10.0
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: PE2
|
||
|
|
dir_pin: !PE3
|
||
|
|
enable_pin: !PE4
|
||
|
|
step_distance: .006275
|
||
|
|
endstop_pin: !PA12
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 330
|
||
|
|
homing_retract_dist: 10
|
||
|
|
homing_speed: 50.0
|
||
|
|
second_homing_speed: 10.0
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: PB9
|
||
|
|
dir_pin: PE0
|
||
|
|
enable_pin: !PE1
|
||
|
|
step_distance: .00125
|
||
|
|
endstop_pin: probe:z_virtual_endstop
|
||
|
|
position_max: 400
|
||
|
|
position_min: -2
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: PB4
|
||
|
|
dir_pin: PB5
|
||
|
|
enable_pin: !PB8
|
||
|
|
step_distance: 0.0111
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: PG12
|
||
|
|
sensor_type: ATC Semitec 104GT-2
|
||
|
|
sensor_pin: PA1
|
||
|
|
control: pid
|
||
|
|
pid_Kp=18.831
|
||
|
|
pid_Ki=0.821
|
||
|
|
pid_Kd=108.044
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 250
|
||
|
|
max_extrude_only_distance: 300
|
||
|
|
pressure_advance: 0
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: PG11
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PA0
|
||
|
|
control: pid
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 130
|
||
|
|
pid_Kp=73.932
|
||
|
|
pid_Ki=1.521
|
||
|
|
pid_Kd=898.279
|
||
|
|
|
||
|
|
[heater_fan hotend_fan]
|
||
|
|
pin: PG14
|
||
|
|
heater: extruder
|
||
|
|
heater_temp: 50
|
||
|
|
fan_speed: 0.5
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: PG13
|
||
|
|
max_power: 0.5
|
||
|
|
|
||
|
|
[controller_fan drivers_fan]
|
||
|
|
pin: PD6
|
||
|
|
|
||
|
|
[filament_switch_sensor sentinel]
|
||
|
|
pause_on_runout: True
|
||
|
|
runout_gcode:
|
||
|
|
M25
|
||
|
|
switch_pin: PA15
|
||
|
|
|
||
|
|
[output_pin beeper]
|
||
|
|
pin: PB0
|
||
|
|
|
||
|
|
[safe_z_home]
|
||
|
|
home_xy_position: 165,165
|
||
|
|
speed: 50
|
||
|
|
z_hop: 10
|
||
|
|
z_hop_speed: 5
|
||
|
|
|
||
|
|
[bed_screws]
|
||
|
|
screw1: 5,5
|
||
|
|
screw2: 165,5
|
||
|
|
screw3: 325,5
|
||
|
|
screw4: 5,325
|
||
|
|
screw5: 165,325
|
||
|
|
screw6: 325,325
|
||
|
|
|
||
|
|
[bed_mesh]
|
||
|
|
speed: 120
|
||
|
|
probe_count: 5,5
|
||
|
|
horizontal_move_z: 5
|
||
|
|
algorithm: lagrange
|
||
|
|
mesh_min : 20,20
|
||
|
|
mesh_max : 310,310
|
||
|
|
mesh_pps: 0
|
||
|
|
|
||
|
|
[probe]
|
||
|
|
x_offset: -40
|
||
|
|
y_offset: 0
|
||
|
|
pin: !PG9
|
||
|
|
speed: 30
|
||
|
|
z_offset: 2
|