2018-01-07 18:20:36 +01:00
|
|
|
# This file contains pin mappings for the Anycubic i3 Mega with
|
|
|
|
|
# Ultrabase from 2017. (This config may work on an Anycubic i3 Mega v1
|
|
|
|
|
# prior to the Ultrabase if you comment out the definition of the
|
|
|
|
|
# endstop_pin in the stepper_z1 section.) To use this config, the
|
|
|
|
|
# firmware should be compiled for the AVR atmega2560.
|
|
|
|
|
|
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: ar54
|
|
|
|
|
dir_pin: !ar55
|
|
|
|
|
enable_pin: !ar38
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^!ar3
|
|
|
|
|
position_min: -5
|
|
|
|
|
position_endstop: -5
|
|
|
|
|
position_max: 210
|
|
|
|
|
homing_speed: 30.0
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: ar60
|
|
|
|
|
dir_pin: ar61
|
|
|
|
|
enable_pin: !ar56
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^!ar42
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 210
|
|
|
|
|
homing_speed: 30.0
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: ar46
|
|
|
|
|
dir_pin: ar48
|
|
|
|
|
enable_pin: !ar62
|
|
|
|
|
step_distance: .0025
|
|
|
|
|
endstop_pin: ^!ar18
|
|
|
|
|
position_endstop: 0.0
|
|
|
|
|
position_max: 205
|
|
|
|
|
homing_speed: 5.0
|
|
|
|
|
|
|
|
|
|
[stepper_z1]
|
|
|
|
|
step_pin: ar36
|
|
|
|
|
dir_pin: ar34
|
|
|
|
|
enable_pin: !ar30
|
|
|
|
|
step_distance: .0025
|
|
|
|
|
endstop_pin: ^!ar43
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: ar26
|
|
|
|
|
dir_pin: ar28
|
|
|
|
|
enable_pin: !ar24
|
|
|
|
|
step_distance: .010799
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: ar10
|
2018-01-22 00:47:34 +01:00
|
|
|
sensor_type: ATC Semitec 104GT-2
|
2018-01-07 18:20:36 +01:00
|
|
|
sensor_pin: analog13
|
|
|
|
|
control: pid
|
2018-01-22 00:47:34 +01:00
|
|
|
pid_Kp: 15.717
|
|
|
|
|
pid_Ki: 0.569
|
|
|
|
|
pid_Kd: 108.451
|
2018-01-07 18:20:36 +01:00
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 245
|
|
|
|
|
|
|
|
|
|
[heater_fan extruder_fan]
|
|
|
|
|
pin: ar44
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: ar8
|
2018-01-22 00:47:34 +01:00
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
2018-01-07 18:20:36 +01:00
|
|
|
sensor_pin: analog14
|
2018-01-22 00:47:34 +01:00
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 74.883
|
|
|
|
|
pid_Ki: 1.809
|
|
|
|
|
pid_Kd: 775.038
|
2018-01-07 18:20:36 +01:00
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 110
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: ar9
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/ttyUSB0
|
|
|
|
|
pin_map: arduino
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 3000
|
|
|
|
|
max_z_velocity: 10
|
2018-01-22 00:47:34 +01:00
|
|
|
max_z_accel: 60
|
