mirror of https://github.com/Desuuuu/klipper.git
145 lines
2.8 KiB
INI
145 lines
2.8 KiB
INI
|
# This file contains common pin mappings for the BIGTREETECH SKR V1.4
|
||
|
|
# board. To use this config, the firmware should be compiled for the
|
||
|
|
# LPC1768 or LPC1769(Turbo).
|
||
|
|
|
||
|
|
# See the example.cfg file for a description of available parameters.
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: P2.2
|
||
|
|
dir_pin: P2.6
|
||
|
|
enable_pin: !P2.1
|
||
|
|
step_distance: .0125
|
||
|
|
endstop_pin: !P1.29
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 235
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: P0.19
|
||
|
|
dir_pin: P0.20
|
||
|
|
enable_pin: !P2.8
|
||
|
|
step_distance: .0125
|
||
|
|
endstop_pin: !P1.28
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 235
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: P0.22
|
||
|
|
dir_pin: !P2.11
|
||
|
|
enable_pin: !P0.21
|
||
|
|
step_distance: .0025
|
||
|
|
endstop_pin: !P1.27
|
||
|
|
position_endstop: 0.0
|
||
|
|
position_max: 300
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: P2.13
|
||
|
|
dir_pin: !P0.11
|
||
|
|
enable_pin: !P2.12
|
||
|
|
step_distance: .010526
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: P2.7
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: P0.24
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 22.2
|
||
|
|
pid_Ki: 1.08
|
||
|
|
pid_Kd: 114
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 260
|
||
|
|
|
||
|
|
#[extruder1]
|
||
|
|
#step_pin: P1.15
|
||
|
|
#dir_pin: P1.14
|
||
|
|
#enable_pin: !P1.16
|
||
|
|
#heater_pin: P2.4
|
||
|
|
#sensor_pin: P0.23
|
||
|
|
#...
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: P2.5
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: P0.25
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 54.027
|
||
|
|
pid_Ki: 0.770
|
||
|
|
pid_Kd: 948.182
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 130
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: P2.3
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 400
|
||
|
|
max_accel: 500
|
||
|
|
max_z_velocity: 10
|
||
|
|
max_z_accel: 100
|
||
|
|
|
||
|
|
|
||
|
|
########################################
|
||
|
|
# TMC2208 configuration
|
||
|
|
########################################
|
||
|
|
|
||
|
|
# For TMC2208 UART
|
||
|
|
# 1) Place jumpers based on configuration
|
||
|
|
# 2) Uncomment below config
|
||
|
|
|
||
|
|
#[tmc2208 stepper_x]
|
||
|
|
#uart_pin: P1.10
|
||
|
|
#microsteps: 16
|
||
|
|
#run_current: 0.800
|
||
|
|
#hold_current: 0.500
|
||
|
|
#stealthchop_threshold: 250
|
||
|
|
#
|
||
|
|
#[tmc2208 stepper_y]
|
||
|
|
#uart_pin: P1.9
|
||
|
|
#microsteps: 16
|
||
|
|
#run_current: 0.800
|
||
|
|
#hold_current: 0.500
|
||
|
|
#stealthchop_threshold: 250
|
||
|
|
#
|
||
|
|
#[tmc2208 stepper_z]
|
||
|
|
#uart_pin: P1.8
|
||
|
|
#microsteps: 16
|
||
|
|
#run_current: 0.650
|
||
|
|
#hold_current: 0.450
|
||
|
|
#stealthchop_threshold: 30
|
||
|
|
#
|
||
|
|
#[tmc2208 extruder]
|
||
|
|
#uart_pin: P1.4
|
||
|
|
#microsteps: 16
|
||
|
|
#run_current: 0.800
|
||
|
|
#hold_current: 0.500
|
||
|
|
#stealthchop_threshold: 5
|
||
|
|
#
|
||
|
|
#[tmc2208 extruder1]
|
||
|
|
#uart_pin: P1.1
|
||
|
|
#microsteps: 16
|
||
|
|
#run_current: 0.800
|
||
|
|
#hold_current: 0.500
|
||
|
|
#stealthchop_threshold: 5
|
||
|
|
|
||
|
|
|
||
|
|
########################################
|
||
|
|
# EXP1 / EXP2 (display) pins
|
||
|
|
########################################
|
||
|
|
|
||
|
|
[board_pins]
|
||
|
|
aliases:
|
||
|
|
# EXP1 header
|
||
|
|
EXP1_1=P1.30, EXP1_3=P1.18, EXP1_5=P1.20, EXP1_7=P1.22, EXP1_9=<GND>,
|
||
|
|
EXP1_2=P0.28, EXP1_4=P1.19, EXP1_6=P1.21, EXP1_8=P1.23, EXP1_10=<5V>,
|
||
|
|
# EXP2 header
|
||
|
|
EXP2_1=P0.17, EXP2_3=P3.26, EXP2_5=P3.25, EXP2_7=P1.31, EXP2_9=<GND>,
|
||
|
|
EXP2_2=P0.15, EXP2_4=P0.16, EXP2_6=P0.18, EXP2_8=<RST>, EXP2_10=<NC>
|
||
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "ssp0"
|
||
|
|
|
||
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|