mirror of https://github.com/Desuuuu/klipper.git
102 lines
2.1 KiB
INI
102 lines
2.1 KiB
INI
|
# This file contains pin mappings for the stock 2020 Creality Ender 5
|
||
|
|
# Pro with the 32-bit Creality 4.2.2 board. To use this config, during
|
||
|
|
# "make menuconfig" select the STM32F103 with a "28KiB bootloader" and
|
||
|
|
# with "Use USB for communication" disabled.
|
||
|
|
|
||
|
|
# If you prefer a direct serial connection, in "make menuconfig"
|
||
|
|
# select "Enable extra low-level configuration options" and select the
|
||
|
|
# USART3 serial port, which is broken out on the 10 pin IDC cable used
|
||
|
|
# for the LCD module as follows:
|
||
|
|
# 3: Tx, 4: Rx, 9: GND, 10: VCC
|
||
|
|
|
||
|
|
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
||
|
|
# turning on the printer with the card inserted. The firmware
|
||
|
|
# filename must end in ".bin" and must not match the last filename
|
||
|
|
# that was flashed.
|
||
|
|
|
||
|
|
# See docs/Config_Reference.md for a description of parameters.
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: PC2
|
||
|
|
dir_pin: PB9
|
||
|
|
enable_pin: !PC3
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: ^PA5
|
||
|
|
position_endstop: 220
|
||
|
|
position_max: 220
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: PB8
|
||
|
|
dir_pin: PB7
|
||
|
|
enable_pin: !PC3
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: ^PA6
|
||
|
|
position_endstop: 220
|
||
|
|
position_max: 220
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: PB6
|
||
|
|
dir_pin: PB5
|
||
|
|
enable_pin: !PC3
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 4
|
||
|
|
endstop_pin: ^PA7
|
||
|
|
position_max: 300
|
||
|
|
position_endstop: 0.0
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
max_extrude_only_distance: 100.0
|
||
|
|
step_pin: PB4
|
||
|
|
dir_pin: PB3
|
||
|
|
enable_pin: !PC3
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 32.342
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: PA1
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PC5
|
||
|
|
control: pid
|
||
|
|
pid_kp: 24.831
|
||
|
|
pid_ki: 1.346
|
||
|
|
pid_kd: 114.532
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 260
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: PA2
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PC4
|
||
|
|
control: pid
|
||
|
|
pid_kp: 66.429
|
||
|
|
pid_ki: 1.197
|
||
|
|
pid_kd: 921.707
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 135
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: PA0
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||
|
|
restart_method: command
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 3000
|
||
|
|
max_z_velocity: 5
|
||
|
|
max_z_accel: 100
|
||
|
|
|
||
|
|
[display]
|
||
|
|
lcd_type: st7920
|
||
|
|
cs_pin: PB12
|
||
|
|
sclk_pin: PB13
|
||
|
|
sid_pin: PB15
|
||
|
|
encoder_pins: ^PB14, ^PB10
|
||
|
|
click_pin: ^!PB2
|