2021-01-24 16:52:14 +01:00
|
|
|
# This file contains pin mappings for the stock 2020 Creality CR6-SE.
|
2021-03-18 18:20:54 +01:00
|
|
|
# To use this config, during "make menuconfig" select the STM32F103
|
|
|
|
|
# with a "28KiB bootloader" and serial (on USART1 PA10/PA9)
|
|
|
|
|
# communication.
|
2021-01-24 16:52:14 +01:00
|
|
|
|
|
|
|
|
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
|
|
|
|
# turning on the printer with the card inserted. The firmware
|
|
|
|
|
# filename must end in ".bin" and must not match the last filename
|
|
|
|
|
# that was flashed.
|
|
|
|
|
|
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PB8
|
|
|
|
|
dir_pin: !PB7
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
microsteps: 16
|
|
|
|
|
endstop_pin: PC4
|
|
|
|
|
position_min: -5
|
|
|
|
|
position_endstop: -5
|
|
|
|
|
position_max: 235
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PB6
|
|
|
|
|
dir_pin: PB5
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
microsteps: 16
|
|
|
|
|
endstop_pin: PC5
|
|
|
|
|
position_min: -2
|
|
|
|
|
position_endstop: -2
|
|
|
|
|
position_max: 235
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PB4
|
|
|
|
|
dir_pin: !PB3
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
rotation_distance: 8
|
|
|
|
|
microsteps: 16
|
|
|
|
|
endstop_pin: probe:z_virtual_endstop
|
|
|
|
|
position_min: -1.5
|
|
|
|
|
position_max: 250
|
|
|
|
|
homing_speed: 4
|
|
|
|
|
second_homing_speed: 1
|
|
|
|
|
homing_retract_dist: 2.0
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
max_extrude_only_distance: 1000.0
|
|
|
|
|
step_pin: PC2
|
|
|
|
|
dir_pin: !PB9
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
rotation_distance: 30.4768
|
|
|
|
|
microsteps: 16
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PA1
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PB1
|
|
|
|
|
control: pid
|
|
|
|
|
# tuned for stock hardware with 200 degree Celsius target
|
|
|
|
|
pid_Kp: 14.32
|
|
|
|
|
pid_Ki: 0.81
|
|
|
|
|
pid_Kd: 63.12
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 275
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PA2
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PB0
|
|
|
|
|
control: pid
|
|
|
|
|
# tuned for stock hardware with 50 degree Celsius target
|
|
|
|
|
pid_Kp: 79.49
|
|
|
|
|
pid_Ki: 1.17
|
|
|
|
|
pid_Kd: 1349.52
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 120
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PA0
|
|
|
|
|
kick_start_time: 0.5
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
|
|
|
restart_method: command
|
|
|
|
|
|
|
|
|
|
# Before printing the PROBE_CALIBRATE command needs to be issued
|
|
|
|
|
# to run the probe calibration procedure, described at
|
|
|
|
|
# docs/Probe_Calibrate.md, to find the correct z_offset.
|
|
|
|
|
[probe]
|
|
|
|
|
pin: PA4
|
|
|
|
|
x_offset: 0.0
|
|
|
|
|
y_offset: 0.0
|
|
|
|
|
z_offset: 0.0
|
|
|
|
|
speed: 2.0
|
|
|
|
|
samples: 5
|
|
|
|
|
|
|
|
|
|
[filament_switch_sensor filament_sensor]
|
|
|
|
|
pause_on_runout: true
|
|
|
|
|
switch_pin: ^!PA7
|
|
|
|
|
|
|
|
|
|
[output_pin LED_pin]
|
|
|
|
|
pin: PA6
|
|
|
|
|
|
|
|
|
|
[static_digital_output daughterboard_communication]
|
|
|
|
|
pins: !PA5
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 500
|
|
|
|
|
max_accel: 500
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
